화웨이 P 스마트 디스플레이 변경 : 작동 방식
Huawei P Smart의 디스플레이에 결함이있는 경우 약간의 기술로 직접 변경할 수 있습니다. 이 실용적인 팁은 수리에 필요한 사항과 진행 방법을 보여줍니다.
화웨이 P 스마트 디스플레이 변경
Huawei P Smart에서 결함이있는 디스플레이를 변경하려면 몇 가지 도구가 필요합니다.
- 기존 디스플레이를 제거하려면 적절한 도구가 필요합니다. 기성품 수리 키트는 실용적입니다. 스크루 드라이버 및 리프팅 도구 외에도 일반적으로 흡입 컵도 들어 있습니다.
- Huawei P Smart의 디스플레이는 접착되어 있으므로 헤어 드라이어를 준비하는 것이 가장 좋습니다. 접착제를 풀 때 사용할 수 있습니다.
- 물론 적절한 교체 디스플레이가 필요합니다.
- 새 디스플레이를 스마트 폰에 다시 연결하려면 강력한 접착 성 액체 접착제가 필요합니다.
Huawei P Smart-디스플레이 수리 매뉴얼
디스플레이 변경을 시작하기 전에 스마트 폰을 끄고 SIM 카드 슬롯을 제거하십시오.
- 뒷면 덮개를 스마트 폰의 나머지 부분과 분리하기 위해 프레임 사이에 얇은 도구를 조심스럽게 밀어 넣습니다. 팁 : 더 나은 취급을 위해 흡입 컵을 사용하십시오.
- 후면 덮개가 풀리고 두 부분을 분리 할 수있게되면 플렉스 케이블이 손상되지 않도록주의하십시오. 이 플렉스 케이블을 조심스럽게 분리하면 스마트 폰이 두 부분으로 나옵니다.
- 이제 배터리 제거를 시작할 수 있습니다. 이렇게하려면 먼저 배터리 위에있는 케이블에 접근하기 위해 다양한 검은 색 접착 커버를 제거해야합니다.
- 배터리의 위와 아래에서 함께 조여진 총 3 개의 금속판을 제거해야합니다.
- 모든 플렉스 케이블을 마지막으로 제거한 경우 배터리를 조심스럽게 제거하십시오. 어떤 식 으로든 구부리거나 손상되지 않도록주의하십시오. 팁 : 헤어 드라이어로 배터리를 약간 가열하면 배터리를 더 쉽게 제거 할 수 있습니다. 바닥에 붙어 있습니다.
- 주의 : 헤어 드라이어로 배터리를 너무 많이 가열하지 마십시오. 헤어 드라이어를 작은 단계에 놓고 팬을 배터리에서 멀리 떨어 뜨려 놓으십시오.
- 배터리를 분리하자마자 디스플레이에서 플렉스 케이블을 분리하십시오. 이제 헤어 드라이어로 디스플레이를 가열하여 접착제를 푸십시오. 그런 다음 얇은 개구부 도구를 사용하여 디스플레이와 프레임 사이의 간격을 조정하십시오.
- 이제 플렉스 케이블을 중간 프레임을 통해 당기면 결함이있는 디스플레이를 제쳐 놓을 수 있습니다. 새 디스플레이를 적용하기 전에 프레임에서 접착제 잔여 물을 완전히 제거하십시오.
- 액체 접착제를 프레임 가장자리에 바르고 새 디스플레이의 플렉스 케이블을 프레임을 통해 배선 한 다음 디스플레이를 프레임에 단단히 누르십시오.
- 이제 배터리 아래에 있던 플렉스 케이블을 먼저 연결하십시오. 수리 세트에는 접착 스트립도 포함되어 있습니다. 여기에 배터리를 조심스럽게 삽입하기 전에 금속 덮개에 씌 웁니다.
- 처음에 분리 한 모든 플렉스 케이블을 연결하십시오. 작은 금속 덮개를 다시 조이는 것을 잊지 마십시오. 마지막으로, 디스플레이의 플렉스 케이블을 다시 연결하고 Huawei P Smart의 후면 덮개와 프레임을 다시 결합하십시오. 이렇게하려면 두 부분을 단단히 눌러야합니다.
다음 실용적인 팁에서 Huawei P Smart가 더 이상 작동하지 않는 경우 발생할 수있는 작업을 확인할 수 있습니다.